Bare Concrete
Best SurfaceThis system is designed to bond to properly prepared concrete. The concrete must be clean, dry, sound, and mechanically ground or shot blasted.
600sqft Commercial Kitchen Epoxy Floor Coating System – Antimicrobial & Non-Slip
Use this to estimate based on your floor size.
★ ★ ★ ★ ★
“DIY project in my basement workshop. Wasn't sure I could pull it off but the instructions were clear and turned out easier than expected.”
Mark D. – Verified Buyer
Fast 3–5 Business Day Delivery Direct To Site
Mixed Fresh in the USA - Guaranteed to Perform
600sqft Commercial Kitchen Epoxy Floor Coating System – Antimicrobial & Non-Slip
Commercial kitchen epoxy flooring coatings, engineered for nonstop kitchens. Trusted by foodservice pros.
When downtime isn’t an option and hygiene isn’t negotiable, you need a floor that works as hard as your crew. This non-slip antimicrobial commercial kitchen epoxy floor coating transforms worn, unsafe surfaces into seamless, high-performance floors built to last through heat, grease, chemicals, and constant washdowns.
What You Get:
- A commercial kitchen epoxy floor coating - Built for the pros that need ultimate floor quality they can rely on.
- A non-slip, easy-clean surface – Built-in aluminum oxide grit provides grip in wet or greasy areas—without chewing through mops or becoming hard to maintain.
- Industrial-strength durability – Withstands scuffs, scrapes, spills, and forklifts—so your floor stays tough under pressure, not just on day one.
- Antimicrobial protection – Resist bacteria, mold, and mildew on the surface to help keep food zones safe and compliant.
- Chemical & thermal resistance – Handles hot oil, degreasers, and daily sanitation with no peeling, chalking, or softening.
- Low-VOC, food-zone safe formulation – Suitable for use in kitchens, prep rooms, and USDA-regulated facilities.
Perfect for:
- Kitchen resurfaces and remodels
- Health-inspected or USDA-regulated facilities
- Walk-ins, dish areas, prep lines
- Food production & processing spaces
- High-traffic back-of-house zones
- Cold storage and washdown zones
- Beverage bottling or dairy plants
- Pharmaceutical or sanitation-sensitive zones
Coverage: 600 sq ft per kit
Finish: Semi-gloss, textured non-slip
Thickness: Approx. 12–15 mils finished build
Resurface once. Forget about it for years.
This isn’t just a fresh coat—it’s a flooring upgrade designed to survive the real-world demands of commercial foodservice. No bubbling. No yellowing. No do-overs.
Try Dymond. One floor is all it takes.
The Strength of Diamond. The Confidence of a Lifetime.
Dymond Coatings are engineered with the same qualities as their namesake — tough, long-lasting, and built to bond for life. That’s why we back every eligible Dymond kit with our Lifetime Promise: if your floor fails due to a verified product defect, we’ll replace the material or issue a credit toward your next job. This warranty applies to complete Dymond systems (primer, base coat, and topcoat) when installed on indoor concrete surfaces and applied according to Dymond’s preparation and application guidelines. Covered issues include delamination caused by faulty resin blends, curing failure due to batch defects, and contamination introduced during manufacturing or packaging. To qualify, the product must be within shelf life, used under proper storage conditions, and installed using only Dymond components.
This warranty does not extend to issues arising from improper surface preparation, substrate contamination, excessive moisture vapor, impact or abuse, substrate movement, or UV discoloration of white/light epoxies. Installations over wood, tile, or outdoor surfaces are excluded unless specifically approved. Cosmetic issues such as texture variation, microbubbling, or minor tint shift are not covered. Warranty coverage is limited to the original purchaser and is non-transferable. Claims must be submitted with photographic evidence of each install stage and full batch documentation. Dymond reserves the right to determine whether the cause of failure falls within warranty scope.
This Promise applies to most DIY and light commercial indoor projects. Larger commercial and industrial installations may be eligible for custom coverage — contact us for terms.
Can This Be Installed Over My Existing Floor?
Yes, in many cases, but the floor underneath has to be clean, solid, and mechanically prepared. The coating can only bond as well as the surface it is applied to.
Every floor is different. When coating over anything other than properly prepared concrete, we strongly recommend applying a small test area first.
Existing Epoxy
Good With PrepThis system can be installed over an existing epoxy coating if the old coating is firmly bonded, clean, sound, and fully deglossed.
Tile
Conditional / Test FirstCan be installed when tile is firmly bonded, clean, degreased, abraded, and tested first. Installation is done at your own risk.
VCT Tile
Conditional / Test FirstMany customers successfully coat over VCT, but the bond depends on tile, adhesive, waxes, moisture, and movement. Installation is at your own risk.
Wood
Conditional / Scratch CoatRequires a scratch coat first. Wood installations are done at your own risk. Always test first.
Required Surface Prep
For a strong bond, the surface must be mechanically prepared. Cleaning alone is not enough.
1
Grind or Shot Blast
The floor must be mechanically ground or shot blasted to create a surface profile the coating can grip.
2
Remove Contamination
Oil, grease, wax, soap residue, dust, old adhesive, sealers, and loose material must be removed before coating.
3
Repair Cracks & Defects
Cracks, holes, divots, and damaged areas should be filled before coating for a stronger, smoother finish.
4
Test First When Unsure
For tile, VCT, wood, unknown coatings, sealed floors, or questionable surfaces, apply a small test area.
Installation Questions We Get Every Week
Click any question to expandDoes the floor need to be ground?
Yes. For a strong bond, the coating needs a clean, mechanically prepared surface profile.
What does delamination mean?
Delamination is when the coating separates, peels, bubbles, or lifts from the floor underneath.
Can this be installed over an existing epoxy?
Often yes, if the existing coating is fully bonded, clean, sound, abraded, and tested first.
Can this be installed over VCT tile?
Sometimes, but the installation depends on the tile, adhesive, waxes, movement, and moisture. Test first.
Can this be installed over wood?
Wood is conditional and normally needs a scratch coat. Always test first.
Can this be installed over tile?
Tile can be conditional. It must be firmly bonded, cleaned, abraded, and tested before a full installation.
Still Not Sure? Test Before You Coat.
Every floor is different. If you are coating over tile, VCT, wood, an unknown coating, sealed concrete, or a questionable surface, apply a small test area first before installing the full system.
The coating can only perform as well as the surface underneath it.
Have a Question We Haven't Answered?
Ask it here. Our product experts are ready and happy to help with any questions you have.
Pro Tip: Always read the full Installation Guide and Product Data Sheets before starting your project. Proper prep is the key to a long-lasting, beautiful floor.
